| Topic Starter |
Message |
 Wiring Cut Location for Ignition Immobiliser? |
NoHandSignals
 14th May 2025 3:39am
|
Forum: Maintenance & Mods (L405) · Replies: 13 · Views: 1356 · Subject: Wiring Cut Location for Ignition Immobiliser? |
| Yes, just cut the single yellow/green Push-To-Start switch -ve wire only. Also connected the immobilization system itself to both the a permanent and accessory live in the passenger fuse box. That was ... |
| Wiring Cut Location for Ignition Immobiliser? |
NoHandSignals
26th Apr 2025 10:43pm
|
Forum: Maintenance & Mods (L405) · Replies: 13 · Views: 1356 · Subject: Wiring Cut Location for Ignition Immobiliser? |
Jimmie, thanks. I will cut the -ve then. Do you know what the two different hot wires do, and which I should splice into for the other side of circuit for this immobilizer?
https://www.fullfatrr. ... |
| Wiring Cut Location for Ignition Immobiliser? |
NoHandSignals
26th Apr 2025 8:34pm
|
Forum: Maintenance & Mods (L405) · Replies: 13 · Views: 1356 · Subject: Wiring Cut Location for Ignition Immobiliser? |
| Okay so, I found the wiring diagram for the Push-to-start switch (thank-you for a great wiki!), but still need some help. There are 2 hot wires into the switch for the Push-to-start system, not sure ... |
| Wiring Cut Location for Ignition Immobiliser? |
NoHandSignals
20th Apr 2025 9:14pm
|
Forum: Maintenance & Mods (L405) · Replies: 13 · Views: 1356 · Subject: Wiring Cut Location for Ignition Immobiliser? |
| OK, so I’m just going to keep it simple and cut behind the push to start switch. Can anyone tell me which different wires here do what? I couldn’t find the push to start in the wiki section wiring ... |
| Wiring Cut Location for Ignition Immobiliser? |
NoHandSignals
20th Apr 2025 7:27pm
|
Forum: Maintenance & Mods (L405) · Replies: 13 · Views: 1356 · Subject: Wiring Cut Location for Ignition Immobiliser? |
Hi Jimmie,
I was worried about cutting the wires near the switch as they just look more like low voltage signal wires than anything else, and the wires that came with the immobiliser are much thicker ... |
| Wiring Cut Location for Ignition Immobiliser? |
NoHandSignals
20th Apr 2025 2:38pm
|
Forum: Maintenance & Mods (L405) · Replies: 13 · Views: 1356 · Subject: Wiring Cut Location for Ignition Immobiliser? |
Looking for guidance on where the wires are, and which wires I should cut to splice this immobilizer in?
I think the diagram is pretty simple, after removing the instrument panel trim though I don' ... |
| Fuel tank guard replacement. |
NoHandSignals
10th Sep 2024 11:29am
|
Forum: Maintenance & Mods (L405) · Replies: 15 · Views: 2988 · Subject: Fuel tank guard replacement. |
Just to confirm, 52mm spanner fits snugly on the prop …
Nice, likely much better than the adjustable wrench I used, and I’m sure just as affordable! |
| Fuel tank guard replacement. |
NoHandSignals
10th Sep 2024 10:58am
|
Forum: Maintenance & Mods (L405) · Replies: 15 · Views: 2988 · Subject: Fuel tank guard replacement. |
Yep, sure did. Definitely a good idea to have a fresh head for tool fitment, and they came with the locking compound already fitted.
Can’t recall exactly but I don’t think they cost too much, a ... |
| Fuel tank guard replacement. |
NoHandSignals
8th Sep 2024 1:48pm
|
Forum: Maintenance & Mods (L405) · Replies: 15 · Views: 2988 · Subject: Fuel tank guard replacement. |
| Those “little ears” do look like a good idea, think I recall reading somewhere though that those “little ears” need removing for some reason on later vehicles, and that the newer version of th ... |
| How do I adjust the ride height at one corner only? |
NoHandSignals
8th Sep 2024 1:36pm
|
Forum: Maintenance & Mods (L405) · Replies: 3 · Views: 667 · Subject: How do I adjust the ride height at one corner only? |
| Thanks, Will. Looks like that one sold and new ones are $6-700 ish. Do you know if there is anything less expensive out there that can make the necessary adjustments? |
| Lowering the subframe slightly - propshaft off ? |
NoHandSignals
8th Sep 2024 3:54am
|
Forum: Maintenance & Mods (L405) · Replies: 14 · Views: 2137 · Subject: Lowering the subframe slightly - propshaft off ? |
| Did my rear ACE pipes With the fuel tank in position and by only dropping the rear subframe a couple of inches, leaving it hanging on a few threads like you did. I did this with the car on a ramp thou ... |
| Fuel tank guard replacement. |
NoHandSignals
8th Sep 2024 3:34am
|
Forum: Maintenance & Mods (L405) · Replies: 15 · Views: 2988 · Subject: Fuel tank guard replacement. |
| Definitely got to undo both ends of the prop, I would say. I thought one end might work at first myself when I changed my tank shield, but couldn’t figure it out. Note I did remove and replace the s ... |
| How do I adjust the ride height at one corner only? |
NoHandSignals
8th Sep 2024 1:37am
|
Forum: Maintenance & Mods (L405) · Replies: 3 · Views: 667 · Subject: How do I adjust the ride height at one corner only? |
Looking for tips on how to do this myself at home, or the cheapest tool that I need buy to let me do this myself at home?
I repaired (successfully I think  ) a leak in the rear left airbag connec ... |
| fuel tank guard cradle |
NoHandSignals
10th Jun 2024 8:07am
|
Forum: Maintenance & Mods (L405) · Replies: 82 · Views: 12270 · Subject: fuel tank guard cradle |
Thanks, Pete. Glad to contribute for once instead of just asking questions  |
| fuel tank guard cradle |
NoHandSignals
9th Jun 2024 6:14pm
|
Forum: Maintenance & Mods (L405) · Replies: 82 · Views: 12270 · Subject: fuel tank guard cradle |
| Word of warning to anyone like me that sees some surface rust underneath the cradle and thinks they should be able to wire brush, treat, and paint it. These cradles rot from the inside. As soon as I p ... |
| |
