Got the door trims off, yous were correct there are 2 bolts holding them on the other side of the door card. Also clipped on, v difficulty to remove without force. Didn't have to take the door card off fully just pulled it out underneath. The most tedious part of the whole thing is the getting to the sat nav surround then removing the buttons, so many little screws. Car is completely driveable without the dash and trims on. Just have to wait a week now

Some parts that have electricals such as the gear surround and rear heater panel will probably be wrapped for handiness.

I can now get all the dirt out from down the sides of the trims in the centre console.. Nasty.. Spotted a few old mouldy chips possibly from McDonald's

Pictures as promised. The black parts are water printed the carbon bits are wrapped due to electrical parts on the hi Lo gear selector and read heat console..

http://db.tt/hmcMtKxO

http://db.tt/sgGE4M1X

http://db.tt/AnGfuojt

http://db.tt/g15x0UAp

Pictures of parts fitted


http://db.tt/A5WpWAzD

http://db.tt/Y4byuiut

http://db.tt/OthuCTPZ

http://db.tt/ow2Vlrej

Thought i would just stick your Pictures up Lolo …..
Got bored waiting for them to download

Click image to enlarge

Thanks for that..

Is there no one to tell me how fabulous it is..?? besides salb of course

Anyone in Ireland looking to get it done, highly recommend Aquaprint in rathcoole..

Fabulous and I like it a job well done  Stand for something or fall for everything !

that looks the dogs, how much does this water printing cost if you dont mind me asking and where can i get some done.

Thanks

It cost €300 so bout £240.. BUT the guy helped me take the parts off and back on which took bout 3.5-4 hours in total!

Fair play to him.

Google hydrographics for places that do it..

What is water printing? [img]http://www.fuelly.com/driver/rob2529/range-rover[img/]
04, 4.4V8, Vogue Oslo Blue with LPG.
"You can sleep in your car, BUT you can't race your house!!!!"

If something can't be fixed with a hammer....... You have yourself an electrical fault!

clever.... ... - .- -.




click link for ,

FORUM WIKI

HOW TO Ǝꓕ∀ꓕOꓤ PICS

workshop manual downloads are in our wiki

.

Clever stuff indeed ….  ====================================

"Open Mike Night " sounded like a lot of fun until i found out i was going to an Autopsy

Clever, but (pardon my ignorance), what did it look like before?

I'd like to be genuine about how good it looks, but don't have (or cannot see) any comparison photos. Si. <This is my name.

I eat rat poison.

A man ain't truly been insulted until he stands buck naked in front of a woman and she didn't even notice. Or care.

Looks good Lolo especially on a black car same as Martins pillar kit does.
If you dont mind me asking why did you do it did you not like the wood or the grey finish? Mine was a blue one!

I wanted to modernize it a bit, I'm young and female, so I felt the walnut was a bit not me, a bit manly and classic..

So it was originally the foundry silver and walnut trim which is very common interior, so at least when I go to resell it might stand out from the crowd a bit..

I have got new chrome spoke steering wheel, black handbrake, black gear selector, black supercharged grille and side vents, supercharged rear lights, rse aftermarket, new style 11 wheels, color coded mirrors and door handles, smoke side repeaters, chrome letters, black tailgate strip and trim, egr blanked, remapped, k&n air filter, LR iPod kit,door sills, interior led light conversion, new high pressure fuel injector, replaced exhaust, and lots of other things..

I have put a lot of time and effort into making it ideal for me.. Brembo 4 piston are next..

This wk end the da and clay comes out..il post some pictures..