Just got my IIDTool from Dan yesterday for my 53 4.4 vogue.
A long list of faults cleared no problem.
Now my question may be simple and already discussed but I couldnt dig anything up searching.

Am I right in thinking the air suspension goes up and down after clearing faults?

When mine did this I immediately got the HDC inactive and Air susp inactive bongs/ messages that then disappeared on restarting the car. Is this normal?

did you play with the tool whilst the engine was running? ... - .- -.




click link for ,

FORUM WIKI

HOW TO Ǝꓕ∀ꓕOꓤ PICS

workshop manual downloads are in our wiki

.

Yes I did. I was scared of draining the battery!

dunno then, hopefully the GAP chaps will let you know.. ... - .- -.




click link for ,

FORUM WIKI

HOW TO Ǝꓕ∀ꓕOꓤ PICS

workshop manual downloads are in our wiki

.

Maybe I should add that after driving again for 10 minutes I had the following faults logged with the IIDTool

32 CAN bus fault
57 air susp inact
23 key 0 random code tolerance increased

Has anyone had any problems with their iiDtool not being seen by the update software or the control software. When I first got it a few months back it connected okay and I was going to check if it needed an update. I have tried it on my PC as well but still the same. Both laptop and PC are running windows 7 one enterprise and the other home premium. I have set the com port to 4 and the laptop sees it just as a USB com port on com 4. The PC sees it as an other device - iiDtool but can't fully load a driver for it.
Is there a driver downloadable for this? Windows 7 is usually pretty good at grabbing a working driver for just about anything you throw at it.
George Traded in my Audi TT 225 for my Range Rover TD6 Autobiography in Java Black. Range Rover now sold.

george, try deleting the updater and app , reboot and then download again.. ... - .- -.




click link for ,

FORUM WIKI

HOW TO Ǝꓕ∀ꓕOꓤ PICS

workshop manual downloads are in our wiki

.

Yes, I had this problem on xp the other day. The updater said it needed updating and after installing the new version it could not detect the iid tool. I reverted to the previous installation using system restore and everything was fine. I happened to be having an email conversation with gap so I reported it to them and they said they'd look into it.

Thanks Stan and Ric for your quick replies.
I had initially tried it on the original updater and controller software and it didn't work so I downloaded the newer software and still nothing. I also did a clean install onto a PC which didn't have it on before and it was the same.
George Traded in my Audi TT 225 for my Range Rover TD6 Autobiography in Java Black. Range Rover now sold.

Downloaded the updater again from a link on the forum, uninstalled reinstalled it's working again. As if by magic.....  Traded in my Audi TT 225 for my Range Rover TD6 Autobiography in Java Black. Range Rover now sold.

 ... - .- -.




click link for ,

FORUM WIKI

HOW TO Ǝꓕ∀ꓕOꓤ PICS

workshop manual downloads are in our wiki

.

Strange issue - since updating my firmware I now ONLY have the Nav On Move option within IID menu.

Gonna try reinstalling firmware.

you installed the wrong firmware, there are two with the 'nav on move' being the second, install the top/first one... ... - .- -.




click link for ,

FORUM WIKI

HOW TO Ǝꓕ∀ꓕOꓤ PICS

workshop manual downloads are in our wiki

.

Yea, just noticed 'Release' and 'Special' and I'm on the latter, flashing now, thanks.

 ... - .- -.




click link for ,

FORUM WIKI

HOW TO Ǝꓕ∀ꓕOꓤ PICS

workshop manual downloads are in our wiki

.