Topic Starter |
Message |
Brake pad warning light. Cutting back wiring . |
lee37Vernon
15th Aug 2020 1:19pm
|
Forum: Maintenance & Mods (L322) · Replies: 5 · Views: 965 · Subject: Brake pad warning light. Cutting back wiring . |
Good man..
I'll take a look, thanks |
Brake pad warning light. Cutting back wiring . |
lee37Vernon
15th Aug 2020 9:34am
|
Forum: Maintenance & Mods (L322) · Replies: 5 · Views: 965 · Subject: Brake pad warning light. Cutting back wiring . |
Thanks Ivan.
I did that originally with no success, I believe there's a break in the wiring somewhere further info the car. I want to remove the wiring as far back towards the binnacle as possible ... |
Brake pad warning light. Cutting back wiring . |
lee37Vernon
14th Aug 2020 7:19pm
|
Forum: Maintenance & Mods (L322) · Replies: 5 · Views: 965 · Subject: Brake pad warning light. Cutting back wiring . |
No one..?😠|
Brake pad warning light. Cutting back wiring . |
lee37Vernon
14th Aug 2020 10:26am
|
Forum: Maintenance & Mods (L322) · Replies: 5 · Views: 965 · Subject: Brake pad warning light. Cutting back wiring . |
Hi.
I've turned off the pad warning bong with my iid tool but am still left with the exclamation mark on the dashboard. Somewhere on the car is a wiring fault and I want to just cut out the pad war ... |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
4th Feb 2017 10:42pm
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
Well my new maf gave pretty much the same readings as my old one but I left it on, 200 miles later the lights stayed off so I think problem solved.. thanks for all ideas |
Rear wiper washer squirt question |
lee37Vernon
4th Feb 2017 10:37pm
|
Forum: Maintenance & Mods (L322) · Replies: 14 · Views: 5531 · Subject: Rear wiper washer squirt question |
Hi.
I'd been putting up with this for the last two years. Last week I fixed it, I used a small 4mm drill bit (by hand, is only plastic )down where the snapped off nozzle goes into the metal shaft. ... |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
17th Jan 2017 11:50pm
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
I can't actually reset adaption on mine either. iid will only do 2006+
Crossing fingers at minute.. |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
17th Jan 2017 6:00pm
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
New Maf giving essentially the same readings as my old one. Still hunts when you try and hold low revs around 1000rpm.
Approx 24 mgh on tick over / 600 rpm
Others same as above pretty much.
... |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
17th Jan 2017 9:07am
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
Thanks for that. That's Exactly what mines doing at the moment..
Eml is off still. I thought it made a difference cleaning Maf but with hindsight the slight change in numbers I got was more likel ... |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
16th Jan 2017 7:28pm
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
73+ vat off my mate at CAF
I've just cleaned it right up, now getting 18 mgh!
Also found a tiny split in a vacuum line in inlet. Also cleaned throttle body.
Going out in it now so fingers ... |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
16th Jan 2017 8:14am
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
I'm getting roughly from yesterday's check
Tick over / 600 - 26.2
1000rpm - 33.8
1500 - 45.8
2000 - 57 |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
15th Jan 2017 9:58pm
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
Thanks.
Lights just come back on. My torque app shows from cold it going from 'open cold ' to ' closed on O2 ' , however my iid says it's not on closed loop so that's thrown me a bit.
Before ... |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
14th Jan 2017 2:23pm
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
I should also say it would appear on the surface to be running absolutely fine. |
4.4 M62 lambda control adaption faults, won't go closed loop |
lee37Vernon
14th Jan 2017 1:49pm
|
Forum: Maintenance & Mods (L322) · Replies: 18 · Views: 6684 · Subject: 4.4 M62 lambda control adaption faults, won't go closed loop |
Bit of background in case related-
PCV valve and pipework replaced last summer. Just checked around for air leaks, can't see any unless the inlet manifold gasket is gone?
Fuel pump died 200 mi ... |
pcv valve queries.. |
lee37Vernon
4th Dec 2016 3:43pm
|
Forum: Technical (L322) · Replies: 13 · Views: 6465 · Subject: pcv valve queries.. |
Hi.
The top two had been replaced before I bought the car, but not the valve. I did replace the other two with silicone hose , the bigger bit I had from another project, I then ordered a metre from ... |
|