| Topic Starter |
Message |
 Limp Mode - Manifold pressure |
leusfx
 11th Aug 2020 1:08pm
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
| Hi, I see now you have got the TDV8 with DPF and ZF 8 HP transmission!? Going back to original remap and EGR ON would be worth to try. BTW who did a remap for you? |
| Limp Mode - Manifold pressure |
leusfx
11th Aug 2020 11:46am
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
You have the TDV8 3.6 with no DPF and with ZF6, right?
I would not worry about going back to original remap while keeping your valves blanked. If you have a DPF it is more complicated and I would no ... |
| FBH Pre-Wiring? |
leusfx
4th Aug 2020 12:56pm
|
Forum: Technical (L322) · Replies: 22 · Views: 12369 · Subject: FBH Pre-Wiring? |
Hey Guys
Would anyone has a PDF file of the installation or retrofitting instructions for Webasto FBH l322 TDV8, please? As far ad I know there is only functional description in the Workshop manual ... |
| TDV8 EGR maintenance |
leusfx
4th Aug 2020 11:28am
|
Forum: Maintenance & Mods (L322) · Replies: 22 · Views: 12932 · Subject: TDV8 EGR maintenance |
| The air intake manifold has a variable intake valve (a.k.a Intake manifold plenum chamber runner control actuator) which allows the two sides of the manifolds to be connected/separated to balance the ... |
| Limp Mode - Manifold pressure |
leusfx
25th Jun 2020 1:22am
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
see attached
https://www.fullfatrr.com/gallery/albums/userpics/19849/normal_LandRover_SSM49537_turbo-actuator-arm-corrosion_201103-1.jpg |
| Limp Mode - Manifold pressure |
leusfx
24th Jun 2020 12:20am
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
L322 Range Rover 3.6L TDV8: turbocharger actuator arm corrosion
In May 2011, Land Rover issued Service Bulletin SSM49537 for Land Rover L322 Range Rover vehicles that had 3.6L TDV8 engines. In these ... |
| NavTool - Carplay, HDMI mirroring, video in etc. 2008 L322 |
leusfx
23rd May 2020 9:44pm
|
Forum: In Car Electronics (L322) · Replies: 167 · Views: 75952 · Subject: NavTool - Carplay, HDMI mirroring, video in etc. 2008 L322 |
| Does anyone know if hdmi input from the navtool can be sent onto the rear seat displays? Or is it working on the main front screen only. |
| TDV8 3.6l MJ 2008 engine wiring loom diagram wanted |
leusfx
21st Feb 2020 5:07pm
|
Forum: Technical (L322) · Replies: 10 · Views: 4526 · Subject: TDV8 3.6l MJ 2008 engine wiring loom diagram wanted |
Could you please provide a link for a TDV8 engine wiring? The link provided is not working.
Thank you. |
| How to determine where coolant leak is coming from |
leusfx
21st Feb 2020 3:46pm
|
Forum: Technical (L322) · Replies: 20 · Views: 5985 · Subject: How to determine where coolant leak is coming from |
Hi,
I had similar issue recently and it turned out to be leaking water pump. I replaced water pump + gasket (50euro) and a hose (50euro). Then did water compression test (got set from amazon also ... |
| Suspension fault |
leusfx
26th Jan 2020 9:33pm
|
Forum: Technical (L322) · Replies: 6 · Views: 4557 · Subject: Suspension fault DTC C1A55-01 |
Hi,
I have exactly the same fault FF TDV8 2008. There is the strip on the dash and says suspension fault.
IID Tool reads RLM-Suspension
C1A55-01 (AF) Ignition switch input circuit - General fai ... |
| Limp Mode - Manifold pressure |
leusfx
16th Jan 2020 1:48pm
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
| That's supposed to be done when idling. |
| Limp Mode - Manifold pressure |
leusfx
15th Jan 2020 5:31pm
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
Rule out faulty turbo actuator with your IIDtool.
Select Live values and compare Command boost actuator control banks 1/2 with Boost pressure actuator banks 1/2 and create log when driving.
Try mo ... |
| Commanded throttle actuator position bank 1 and 2 always 0. |
leusfx
15th Jan 2020 2:52pm
|
Forum: Technical (L322) · Replies: 0 · Views: 800 · Subject: Commanded throttle actuator position bank 1 and 2 always 0. |
Good afternoon,
I would greatly appreciate your opinion.
IID tool live values show commanded throttle actuator position bank 1 and 2 is always 0.
Actual position is 4.98% during drive -all the ... |
| Limp Mode - Manifold pressure |
leusfx
15th Jan 2020 1:19pm
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
What is your trouble code when Limp mode happens?
Is it P023d-22 -
(Manifold absolute preassure - turbocharger/supercarger boost senzor A correlation - general signal failure.)?
This is most of ... |
| Limp Mode - Manifold pressure |
leusfx
14th Jan 2020 12:46am
|
Forum: Technical (L322) · Replies: 72 · Views: 35535 · Subject: Limp Mode - Manifold pressure |
Thanks.
I'd like to share my solution to the issue. Eventually, I used Leister Triac ST heater gun with PA (nylon) settings and PA 6.6 welding rod. I did not have previous experience welding plastics ... |
| |
