| Topic Starter |
Message |
 front cv boots split |
PDC
 7th Jul 2025 9:32pm
|
Forum: Technical (L322) · Replies: 8 · Views: 574 · Subject: front cv boots split |
| I’ve only just finished replacing pretty well everything that you can see. I did also primer and top coat all of the new parts and then waxed them. Hopefully it will still look like that in a few ye ... |
| AC hose burst - any advice? (edited topic) |
PDC
6th Jul 2025 9:54pm
|
Forum: Technical (L322) · Replies: 7 · Views: 370 · Subject: AC hose burst - any advice? (edited topic) |
| It's a doddle of a job to replace, just a bolt on either end and from memory a fixing bracket at the Bottom of the engine. But you will need to re-gas afterwards. |
| AC hose burst - any advice? (edited topic) |
PDC
6th Jul 2025 9:32pm
|
Forum: Technical (L322) · Replies: 7 · Views: 370 · Subject: AC hose burst - any advice? (edited topic) |
| Yes that one is defiantly the AC hose. It leads from the AC rad to the compressor. |
| AC hose burst - any advice? (edited topic) |
PDC
6th Jul 2025 8:04pm
|
Forum: Technical (L322) · Replies: 7 · Views: 370 · Subject: AC hose burst - any advice? (edited topic) |
It's hard to see from the photo which pipe it is that has split. But all in that area are easy to replace.  |
| Rattling noise engine bay l322 5.0 supercharged |
PDC
6th Jul 2025 7:55pm
|
Forum: Technical (L322) · Replies: 10 · Views: 780 · Subject: Rattling noise engine bay l322 5.0 supercharged |
My chains sound noisier than yours but with half the amount of play in the chain, but I would defiantly say that is way too much slack and need doing asap.
The noise to me though sounds like a dry sc ... |
| Unidentified connection/wire in drivers wheel well. |
PDC
6th Jul 2025 6:38pm
|
Forum: Technical (L322) · Replies: 4 · Views: 333 · Subject: Unidentified connection/wire in drivers wheel well. |
| I will have a stab at, transfer box breather pipe.... |
| Welding in rear repair panels |
PDC
6th Jul 2025 3:33pm
|
Forum: Maintenance & Mods (L322) · Replies: 3 · Views: 506 · Subject: Welding in rear repair panels |
This might be helpful. the 1st photo is before the jacking point was welded in and the second afterwards.
https://www.fullfatrr.com/gallery/albums/userpics/20075/normal_c347a00b-e1ea-43ae-82bb- ... |
| front cv boots split |
PDC
6th Jul 2025 3:10pm
|
Forum: Technical (L322) · Replies: 8 · Views: 574 · Subject: front cv boots split |
I also used this for the CV boots from eBay at £12.00 It tightens with a spanner so you can really clamp on the clips. Just remember not to over pack the boots with too much grease!
CV axle Boot ... |
| front cv boots split |
PDC
6th Jul 2025 3:03pm
|
Forum: Technical (L322) · Replies: 8 · Views: 574 · Subject: front cv boots split |
| I've just completed the job. I used aTITAN TTB653SDS 5.9KG ELECTRIC SDS PLUS CHISEL / DRILL. It was only £60 and they popped straight out using this. I also removed the front ball joints using it. It ... |
| What Did You Do In Your Full Fat Today |
PDC
26th May 2025 11:26am
|
Forum: General · Replies: 5749 · Views: 2099761 · Subject: What Did You Do In Your Full Fat Today |
| At long last, what began as a simple front caliper refurbishment turned into a full overhaul. All the suspension arms, drop links, and steering arms have been replaced with Lemförder parts. I also re ... |
| Back with another Supercharged! A 5.0 this time! |
PDC
26th May 2025 11:05am
|
Forum: My Range Rover · Replies: 276 · Views: 59573 · Subject: Back with another Supercharged! A 5.0 this time! |
| Great reading. many thanks! |
| Rear arch / sill rust |
PDC
26th May 2025 10:42am
|
Forum: Maintenance & Mods (L322) · Replies: 17 · Views: 1614 · Subject: Rear arch / sill rust |
| I had mine done last year. It wasn’t cheap — around £2,300 for both sides — and I supplied the replacement panels myself. What I liked was that, wherever possible, they bonded the panels rather ... |
| Back with another Supercharged! A 5.0 this time! |
PDC
26th May 2025 10:08am
|
Forum: My Range Rover · Replies: 276 · Views: 59573 · Subject: Back with another Supercharged! A 5.0 this time! |
| Cheers for that David. At least I now know that there is no way of pressing them out. I will just go carefully when driving them out by hand. |
| Different underbody panels between SC and NA L322s? |
PDC
26th May 2025 8:57am
|
Forum: Technical (L322) · Replies: 2 · Views: 345 · Subject: Different underbody panels between SC and NA L322s? |
| Hi Brandon, I’ve just noticed that you are also missing the gearbox sump protector frame and panel. That will stop any stones from been kicked up & hitting the plastic sump on the transmission. ... |
| Back with another Supercharged! A 5.0 this time! |
PDC
25th May 2025 11:14pm
|
Forum: My Range Rover · Replies: 276 · Views: 59573 · Subject: Back with another Supercharged! A 5.0 this time! |
Hi David, how did you drive out the bush with one side having a flange on it and getting in the way. I'm thinking of doing mine soon. Do you also think a 10 Ton press will be up to the job?
Cheers, ... |
| |
